Tips and tricks¶
- How do I update my local copy of ZTPServer from GitHub?
- My server keeps failing to load my resource files. What’s going on?
- How do I validate the format of my config files?
- How do I debug the ZTP Server provisioning process?
- How do I disable / enable ZTP mode on a switch
- How can I test ZTPServer without having to reboot the switch every time?
- What is the recommended test environment for ZTPServer?
- How do I override the default system-mac in vEOS?
- How do I override the default serial number or system-mac in vEOS?
How do I update my local copy of ZTPServer from GitHub?¶
Automatically¶
- Go to the ZTPServer directory where you previously cloned the GitHub repository and execute:
./utils/refresh_ztps [-b <branch>] [-f <path>]
<branch> can be any branch name in the Git repo. Typically this will be one of:
- “master” - for the latest release version
- “vX.Y.Z-rc” - for beta testing the next X.Y.Z release-candidate
- “develop” (DEFAULT) - for the latest bleeding-edge development branch
<path> is the base directory of the ztpserver installation.
- /usr/share/ztpserver (DEFAULT)
Manually¶
Remove the existing ZTPServer files:
rm -rf /usr/share/ztpserver/actions/*
rm -rf /usr/share/ztpserver/bootstrap/*
rm -rf /usr/lib/python2.7/site-packages/ztpserver*
rm -rf /bin/ztps*
rm -rf /home/ztpuser/ztpserver/ztpserver.egg-info/
rm -rf /home/ztpuser/ztpserver/build/*
Go to the ZTPServer directory where you previously cloned the GitHub repository, update it, then build and install the server:
bash-3.2$ git pull
bash-3.2$ python setup.py build
bash-3.2$ python setup.py install
My server keeps failing to load my resource files. What’s going on?¶
Did you know?
a:b is INVALID YAML
a: b is VALID YAML syntax
Check out YAML syntax checker for more.
How do I validate the format of my config files?¶
To validate config files use ztps --validate
:
[ztpsadmin@ztps ~]$ ztps --validate
Validating neighbordb ('/usr/share/ztpserver/neighbordb')... Ok!
Validating definitions...
Validating /usr/share/ztpserver/definitions/torb-withImageUpgrade... Ok!
Validating /usr/share/ztpserver/definitions/torb... Ok!
Validating /usr/share/ztpserver/definitions/tora-withImageUpgrade... Ok!
Validating /usr/share/ztpserver/definitions/tora... Ok!
Validating resources...
Validating /usr/share/ztpserver/resources/tor_hostnames... Ok!
Validating /usr/share/ztpserver/resources/ip_loopback... Ok!
Validating /usr/share/ztpserver/resources/ip_vlan100... Ok!
Validating /usr/share/ztpserver/resources/mgmt_subnet... Ok!
Validating nodes...
Validating /usr/share/ztpserver/nodes/001122334456/pattern... Ok!
Validating /usr/share/ztpserver/nodes/001122334456/definition... Ok!
Validating /usr/share/ztpserver/nodes/001122334455/pattern... Ok!
Validating /usr/share/ztpserver/nodes/001122334455/definition... Ok!
Validating /usr/share/ztpserver/nodes/001122334457/pattern... Ok!
Validating /usr/share/ztpserver/nodes/001122334457/definition... Ok!
How do I debug the ZTP Server provisioning process?¶
If ZTP Server is running via wsgi, Check the Apache log files. Separate log files can be designated for ZTP Server’s wsgi with the following:
<VirtualHost *:8080> CustomLog logs/ztpserver-access_log common ErrorLog logs/ztpserver-error_log ... </VirtualHost>
Run the standalone ZTP Server binary in debug mode and log the output to a file:
ztps --debug 2>&1 | tee ztps.log
After changing configuration directives in neighbordb, a definition, etc, you may need to remove the node directory of the node-under-test before retrying ZTP on the node. This will ensure that ZTP Server matches the node against neighbordb instead of
nodes/<serialnum>/pattern
.The
bootstrap
script may be manually run from a switch instead of going through an entire reload/ZTP cycle. To do this, download the script to the switch, then run it locally:switch# bash wget http://ztpserver:8080/bootstrap switch# bash chmod +x bootstrap switch# bash sudo ./bootstrap
On the client side, make sure you use XMPP (best) or remove syslog (second best) logging - you can configure that in bootstrap.conf.
When requesting support, please include the output from the server (running in debug mode) and the console/log output from the switch.
How do I disable / enable ZTP mode on a switch¶
By default, any switch that does not have a startup-config
will enter ZTP mode to attempt to retrieve one. This feature was introduced in EOS 3.7 for fixed devices and EOS 4.10 for modular ones. In ZTP mode, the switch sends out DHCP requests on all interfaces and will not forward traffic until it reboots with a config.
To cancel ZTP mode, login as admin and type zerotouch cancel
. This will trigger an immediate reload of the switch, after which the switch will be ready to configure manually. At this point, if you ever erase the startup-config and reload, the switch will edn up ZTP mode again.
To completely disable ZTP mode, login as admin and type zerotouch disable
. This will trigger an immediate reload of the switch after which the switch will will be ready to configure manually. If you wish to re-enable ZTP, go to configure mode and run zerotouch enable
. The next time you erase the startup-config and reload the switch, the switch will end up ZTP mode again.
Note
vEOS instances come with a minimal startup-config so they do not boot in to ZTP mode by default. In order to use vEOS to test ZTP, enter erase startup-config
and reload.
How can I test ZTPServer without having to reboot the switch every time?¶
From a bash shell on the switch:
# retrieve the bootstrap file from server
wget http://<ZTP_SERVER>:<PORT>/bootstrap
# make file executable
sudo chmod 777 bootstrap
# execute file
sudo ./bootstrap
What is the recommended test environment for ZTPServer?¶
The best way to learn about and test a ZTPServer environment is to build the server and virtual (vEOS) nodes with Packer. See https://github.com/arista-eosplus/packer-ztpserver for directions.
If you setup your own environment, the following recommendations should assist greatly in visualizing the workflow and troubleshooting any issues which may arise. The development team strongly encourages these steps as Best Practices for testing your environment, and, most of these recommendations are also Best Practices for a full deployment.
During testing, only - run the standalone server in debug mode:
ztps --debug
in a buffered shell. NOTE: do NOT use this standalone server in production, however, except in the smallest environments ( Approx 10 nodes or less, consecutively).Do not attempt any detailed debugging from a virtual or serial console. Due to the quantity of information and frequent lack of copy/paste access, this if often painful. Both suggested logging methods, below, can be configured in the Bootstrap configuration.
(BEST) Setup XMPP logging. There are many XMPP services available, including ejabberd, and even more clients, such as Adium. This will give you a single pane view of what is happening on all of your test switches. Our demo includes ejabberd with the following configuration:
- Server: im.ztps-test.com (or your ZTPServer IP)
- XMPP admin user: ztpsadmin@im.ztps-test.com, passwd eosplus
(Second) In place of XMPP, splecify a central syslog server in the bootstrap config.
How do I override the default system-mac in vEOS?¶
Add the desired MAC address to the first line of the file /mnt/flash/system_mac_address, then reboot (Feature added in 3.13.0F)
[admin@localhost ~]$ echo 1122.3344.5566 > /mnt/flash/system_mac_address
How do I override the default serial number or system-mac in vEOS?¶
As of vEOS 4.14.0, the serial number and system mac address can be configured with a file in /mnt/flash/veos-config. After modifying SERIALNUMBER or SYSTEMMACADDR, a reboot is required for the changes to take effect.
SERIALNUMBER=ABC12345678
SYSTEMMACADDR=1122.3344.5566